Trosų alyva

Trosų alyvos

Skvarbi trosų priežiūros alyva

Purškiama kranų lynų alyva

FUNCOL SKL 1 is liquid as the vehicle for the anti-rust lubricant part is a solvent. The choice of solvent has two reasons: The first because it penetrates more easily and correctly within the strands of the ropes, the second for the ease of distribution which can take place by spraying or manually with a brush.

This product has been designed for the maintenance of ropes and therefore reflects all the needs of the case

In addition, our main competitors for steel wire ropes products for maintenance also use solvent as a vehicle.

Lubricating greases, even when they are very soft (NLGI 00, 0, 1), are difficult to dispense and do not penetrate sufficiently inside the strands of the rope.

Please take note that after dispensing FUNCOL SKL1, the solvent evaporates and leaves on the strands the right amount of product to lubricate and rust preventing; obviously, the film left has a greater consistency.

Wire rope oil lubrication

There are two types of wire rope lubricants, penetrating and coating. Penetrating lubricants contain a petroleum solvent that carries the lubricant into the core of the wire rope then evaporates, leaving behind a heavy lubricating film to protect and lubricate each strand (Figure 2). Coating lubricants penetrate slightly, sealing the outside of the cable from moisture and reducing wear and fretting corrosion from contact with external bodies.

Figure 2. Foam Penetrating Type Wire Rope

Both types of wire rope lubricants are used. But because most wire ropes fail from the inside, it is important to make sure that the center core receives sufficient lubricant. A combination approach in which a penetrating lubricant is used to saturate the core, followed with a coating to seal and protect the outer surface, is recommended. Wire rope lubricants can be petrolatum, asphaltic, grease, petroleum oils or vegetable oil-based (Figure 3).

Figure 3. Grease Lubed Wire Rope

Užpurškus alyvą ir nugaravus tirpikliui, FUNCOL SKL 1 ant darbinio paviršiaus palieka ploną, mažai lipnią ypač efektyvią apsauginę plėvelę.

Pritaikymas

• Visų rūšių plienų, pynimo, gijų skaičiaus, šerdies medžiagos trosams ir kabeliams
• Kasdienei kėlimo technikos, kranų priežiūrai, profilaktiniam jų sutepimui
• Trosam ir lynams kai reikalinga ne per riebi (posausė) jų paviršiaus danga
• Generaliniam trosų aptarnavimui kai reikalingas jo pilnas impregnavimas tepalu iki pačios šerdies
• Standiems trosam ir lynams kai konsistenciniu tepalu nepavyksta pilnai sutepti jo gijų
• Velkių, kranų, elevatorių, semtuvių, pakabinamų tiltų, liftų, laivų, transporterių, gręžimo ir kitų įtaisų trosams, bokštus laikantiems lynams, gervių trosams

Specifikacijos

Swiss Federal Transport Office "wire lubricants"

DSB 80 kategorija

Patarimai

Vidutinė išeiga : 40gr / m2

Tinka išpurškimui rankiniu ar automatiniu pneumo pulverizatoriumi.

Siekiant geresnio antikorozinio efekto naudoti ant prieš tai nuvalyto paviršiaus, o užpurškus skystį, palikti trosą džiūti kelias valandas

Techniniai parametrai

Išvaizda                                           vizualiai                    -               skysta alyva

Spalva                                             vizualiai                    -               ruda      

Specifinis tankis @ 25°C                 ASTM D 1298       kg/dm3              0,830

Tankis @ 40°C                                ASTM D 445            cSt             22

Pliūpsnio taškas, PM                       ASTM D 93               °C             ≥ 62

Nuplovimas vandeniu                               -                         -              netirpsta

Vario korozijos testas                         IP 130                pakopa          1 a